Maximum Maestro 2S Manual de usuario descargar pdf

MAESTRO 2-S

INSTALLATION

PROPER INSTALLATION IS IMPORTANT. IF YOU NEED ASSISTANCE, CONSULT A CONTRACTOR, ELECTRICIAN

OR TELEVISION ANTENNA INSTALLER (CHECK WITH YOUR LOCAL BUILDING SUPPLY, OR HARDWARE STORE

FOR REFERRALS). TO PROMOTE CONFIDENCE, PERFORM A TRIAL WIRING BEFORE INSTALLATION.

When assembling the wind direction sensor

to the Z-mast, make certain that terminal #3

is aligned with the Z-mast arm.

Slide the stub masts through the rubber boots and

insert the stub masts into the bottom of the sensors. Secure

with the cotter pins. Coat all wire connections with silicone

sealant and slip the boots over the sensors.

TERMINAL #3

MUST ALIGN

WITH Z-MAST

ARM

TERMINAL

WIND DIRECTION

SENSOR

BOSS

WIND DIRECTION

SENSOR

COTTER

STRAIGHT

STUB MAST

Z-STUB

MAST

5-CONDUCTOR

CABLE

2-CONDUCTOR

CABLE

BOOT

WIND SPEED

SENSOR

Feed the terminal lug end of the five-conductor

cable through the other rubber boot and connect

the lugs to the terminals on the bottom of the wind-direction

sensor. (Do NOT adjust the nuts that are already on the sensor).

The red sleeve indicates wire #1.

Feed the teminal lug end of the 2-conductor cable through one

of the rubber boots and connect the lugs to the terminals on the

bottom of the wind speed sensor. (Do NOT adjust the nuts

that are already on the sensor). The polarity does not matter.

Determine where you are going to locate both the

rooftop sensors and the read-out.

Samuel Barnett Boulevard

New Bedford, MA 02745

(508) 995-2200

2-CONDUCTOR

CABLE

BOOT

BOSS

T-4

(S & SW)

T-2

(E & SE)

T-3

(POWER)

T-5

(W & NW)

TERMINAL-1

(N & NE)

RED

SLEEVE

5-CONDUCTOR

CABLE

BOOT

Secure the sensors and stub masts to your antenna mast (not supplied) with

the two hose clamps. Align the wind-direction Z-mast arm to true North.

Radio Shack and similar stores have a selection of tall masts and roof

mounting brackets. Choose a mount that best suits your location and

provides at least eight feet of vertical clearance above objects on the roof.

HOSE

CLAMPS

NORTH

1 2 3 4 5 6

MAESTRO 2-S 1

Indice de contenidos

Pagina 1 - MAESTRO 2-S

MAESTRO 2-SINSTALLATIONPROPER INSTALLATION IS IMPORTANT. IF YOU NEED ASSISTANCE, CONSULT A CONTRACTOR, ELECTRICIAN OR TELEVISION ANTENNA INSTALLER

Pagina 2

MAESTRO 2-SINSTALLATION(continued)Samuel Barnett BoulevardNew Bedford, MA 02745(508) 995-22006Follow the instructions supplied with the antenna mount

Pagina 3

MAESTRO 2-SOPERATIONReset the gust register needle byturning the knob counter-clockwise.Turning the knob counter-clockwise will eventually contact the

Pagina 4

MAESTRO 2-STROUBLE SHOOTINGWIND SPEEDWIND DIRECTION 1. Disconnect the two wind-speed wires from the back of the brass read-out.

Pagina 5

IMPORTANT ADDITIONAL INFORMATION Components: Along with the indicator, the following components are included with this instrument:

Pagina 6

30 SAMUEL BARNET BOULEVARD  NEW BEDFORD, MASSACHUSETTS 02745 U.S.A. TEL. 508.995.2200  WWW.MAXIMUM-INC.COM  FAX 800.989.2580 Electrical Damage

Comentarios a estos manuales

Sin comentarios

Maximum Maestro 2S Manual de usuario

Busca en linea o descarga Manual de usuario para Instrumentos de medición Maximum Maestro 2S. Maximum Maestro 2S User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Maximum Maestro 2S